全國咨詢熱線

常見問題

當前位置:首頁 - 新聞資訊 > 常見問題 >

自動感應門常見的故障和處理方法!

來源:http://www.czygjs.com 日期:2021-03-11 發布人:admin
自動感應門已經應用的相當廣泛,便捷的使用方式得到了人們的普遍喜愛。今天我們要談的是感應自動門的偽故障,是指因外部因素造成的故障現象,而不是機組部件的故障,偽故障自己就很容易進行修復,如果判斷是主機內部的電器或機械出現了問題,那就要和廠家進行聯系,由廠家為您負責排出故障及更換配件。那當我們遇到了偽故障時應當怎么處理呢?
Automatic induction door has been widely used, convenient way of use has been widely loved by people. Today we are going to talk about the pseudo fault of the induction automatic door, which refers to the fault phenomenon caused by external factors, rather than the fault of the unit components. The pseudo fault can be easily repaired by itself. If it is judged that there is a problem with the electrical or mechanical equipment inside the main engine, it is necessary to contact the manufacturer, who is responsible for troubleshooting and replacing the parts for you. What should we do when we encounter a fake fault?
常見的一個偽故障,門扇停止運動,首先要看看是否有給自動機組送電,檢查移動門扇是否有拖地現象,若由此現象,門在啟動時很吃力,主控制器會誤認為有障礙而運行保護作用,使門扇停止運動。檢查門扇的吊具滑輪部分是不是脫離軌道,還要留意一下感應自動門是否安裝了“安全光線”,安全光線的受光器上有灰塵覆蓋也會引起門扇不動。
A common false fault is that the door leaves stop moving. First of all, it is necessary to check whether there is power supply to the automatic unit, and check whether the moving door leaves drag the floor. If this phenomenon occurs, the door is very difficult to start, and the main controller will mistakenly think that there is an obstacle and operate to protect the door leaves, so that the door leaves stop moving. Check whether the pulley part of the spreader of the door leaf is out of the track, and also pay attention to whether the induction automatic door is installed with "safety light". If the light receiver of the safety light is covered with dust, the door leaf will not move.
                        濟南感應自動門
第 二個偽故障就是門扇自己不停的開關,可能有活動的物體進入感應器的感應范圍會引起感應器的誤動作。檢查它的感應探頭,看是否感應探頭的探測范圍調的太向下,導致感應器裝置誤以為有物體在移動,詳細檢查感應自動門附近有無物體發出的強烈點播,也可能干擾到感應器。
The second false fault is that the door leaves keep on switching. There may be moving objects entering the sensing range of the sensor, which will cause the sensor misoperation. Check its induction probe to see if the detection range of the induction probe is adjusted too downward, resulting in the sensor device mistaking that there is an object moving. Check in detail whether there is a strong demand from an object near the induction automatic door, which may also interfere with the sensor.
第三個偽故障就是,使用時間較長的自動感應門會有行走時聲音大不流暢的狀況。那就得注意給軌道和滑輪添加潤滑油,還要注意清理。檢查五金吊具,部分吊具連接有松動需重新加固。
The third false fault is that the automatic induction door, which has been used for a long time, will make a loud sound and not smooth when walking. Then pay attention to add lubricating oil to the track and pulley, and also pay attention to cleaning. Check the hardware spreader. Some spreaders are loose and need to be reinforced again.
第四個常見的偽故障就是移動門扇的反應慢,可能是因為感應器的探測范圍小,感應器的內部有灰塵,或者移動門扇的門體重量超出自動門馬達的承受范圍,也會引起此現象的發生。
The fourth common false fault is the slow response of the moving door leaf, which may be caused by the small detection range of the sensor, dust inside the sensor, or the weight of the moving door leaf exceeds the bearing range of the automatic door motor.
感謝您的閱讀,希望以上內容對您有所幫助,如您想了解更多精彩內容請點擊我們的官網:濟南感應自動門http://www.czygjs.com 。
Thank you for reading, hope the above content is helpful to you, if you want to know more wonderful content, please click our official website: Jinan induction automatic door http://www.czygjs.com  .

上一篇:玻璃隔斷表面是否會發霉變黑!
下一篇:最后一頁

欧美日韩视费观看视频_欧美日韩免费高清视视频_欧美日韩精品一区二区在线